|
|
 |
 |
 |
 |
    Round Pipe Line System manufactures 3" through 14" round pipe in 2 through 10-foot lengths in 24-gauge mild steel and lighter, this system will produce up to 45,000 feet of pipe in an 8 hour shift Pipe roll machines can accept the full output produced by snap-lock© machines when coupled with the automatic feed tables. They can be equipped with feed table for manual operation Purchase the complete system or start with the individual machines and add components as your requirements for greater production increase |
    |
 |
  Shown above are two shapes typically used on this system The No. 24RF-6 Panel Machine will form shapes like Acme Lock© and Hemming Edge©. It's a high production machine designed to produce special shapes not requiring nine forming stations of the No. 24RF |
  NOR-24RF |
The No. 24RF Snap-Lock Panel machine (photo to the left) forms female and male locks on varying blank width in one pass This Machine is a high production machine designed to increase output and cut cost in the fabrication of pipe and duct section in the NOR Service inc. pipe system The nine-station No. 24RF is equipped with a micrometer dial-type upper spindle adjustment for easy changing from one gauge to another |
The six station No. 24RF-6 is equipped with a micrometer dial-type upper spindle adjustment for easy changing from one gauge to another |
Shown to the right are two locks typically used on this system The modified "R" Snap Lock© and The Duck Lock© The one most preferred by most Oval Pipe Manufacturers -- is the Button Lock© |
 Button Lock 24RF  Modified "R" Lock 24RF |
 Duct Lock 24RF |
 * |
 |
| No. 24RF-6 Snap-Lock Panel Machine Floor Space 6'6" x 3' No. 24RF Snap-Lock Panel Machine Floor Space 6'6" x 5'4"  |
Capacity, max --------------------------------- Forming Stations 24RF-6 ----------------- 24RF -------------------- Locks Formed 24RF-6 --------------------- Acme Lock ------------ Hemmed Edge --------- Locks Formed 24RF ------------------------ Duck Lock ------------- Button Lock ----------- Modified "R" Lock - Pitch --------------------------------------------- Spindle Diameter ---------------------------- Horz. Center Between Spindles ---------- Blank Capacity ------------------------------- Vertical Top Roll Adj. ---------------------- Forming Speed -------------------------------- Motor -------------------------------------------- |
24-gauge mild steel 6 on each head 9 on each head 2 most common see lock above see lock above 3 most common see lock above see lock above see lock above 2-3/4" equal gearing 1" hardened and ground 5" 9" to 46" (3" thru 14" dim. pipe) .062 150 FPM 3 HP,Slow Speed, 220/440 Volt, 60 Cycle, 3 Phase |
|
 |
| No. NOR 155 or No. NOR 1510 Automatic Transfer Table Eliminate the necessity of wide spacing of blanks entering the No. 24RF Panel-Type Snap-Lock© Machine with this automatic transfer table. Your line speed can increase by 50% as compared to hand feeding The No. 155 or No. 1510 Automatic Transfer Table is used in both the oval and round pipe line systems. Eliminates the manual feeding of the No. R5 and No. R10 Round Pipe Roll and the No. OV10 Combination Oval/Round Pipe Roll Short crimps are eliminated with the new self-compensating length adjustment gauge which will handle blanks with +/- 1/4" variance in length |
| * |
|
| No. 155 5' Automatic Transfer Table Floor Space 8'9" x 6'3" No. 1510 10' Automatic Transfer Table Floor Space 13'9" x 6'3" |
Blank Width ----------------------------------- Pipe Diameter --------------------------------- Pipe Length--No. 155 ------------------------ No. 1510 ---------------------- Protective Guarding ------------------------- Air Supply -------------------------------------- Motor -------------------------------------------- |
9" thru 46" 3" thru 14" 2' to 5' 2' to 10' yes 90 PSI (2) 1/2 HP, 220/440 Volt, 1725 RPM, 60 Cycle, 3 Phase |
|
|
| Nor Service inc. Pipe Roll Machines are versatile and easily adaptable with the No. NOR-24RF panel type snap-lock© machines and feed tables. They will shapely reduce the cost of manufacturing pipe and duct sections All rolls are powered... operating at 95 FPM Both models can roll, crimp and bead 24-gauge and lighter mild steel in one pass Two models are available with capabilities of 2' to 5' or 2' to 10' pipe Manual feed tables are available when pipe rolls are not used with a feed table |
  No. R5 |
|
| * |
|
| No. R5 5' Round Pipe Roll Machine Floor Space 7'6" x 2' No. R10 10' Round Pipe Roll Machine Floor Space 13' x 2'6" |
Capacity, max ----------------------------- Pipe Diameter ---------------------------- Pipe Length -----No.R5 ----------------- -----No. R10 --------------- Forming Speed --------------------------- Roll Diameter --Top --------------------- --Bottom/Radial ------ Air Supply ---------------------------------- Motor ---------------------------------------- |
24-gauge mild steel 3" and larger up to 5' up to 10' 95 FPM 1-3/4" 2" (3/8" line) 90 PSI 2 HP, 220/440 Volt, 1725 RPM, 60 Cycle, 3 Phase timing belt drive |
|
|
| No. NOR-OV10 Oval/Round Pipe Roll Machine Nor Service inc. Oval/Round Pipe Roll Machines are versatile and easily adaptable with the No. 24RF Panel-type Snap-Lock© machines and feed tables. Thay will sharply reduce the cost of manufacturing pipe and duct sections. All rolls are powered, operating at 95 FPM for round - 48FPM for oval and can crimp and bend 24 gauge and lighter mild steel in one pass If NOR-OV10 is used with in optional manual feed table. an electrical control cabinet with motor starters and oval shape control timers is required For more information please contact at E-Mail / Phone: 815.232.8379 Fax: 815.232.4108 |
| * |
|
| No. NOR-OV10 10' Oval/Round Pipe Roll Machine Floor Space 13' x 2'6" |
Capacity, max ------------------------------ Pipe Diameter ----------------------------- Length --------------------------------------- Pipe Diameter Round -------------------- Forming Speed --Round ----------------- --Oval ------------------- Roll Diameter ---Top --------------------- ---Bottom/Radial ------- Air Supply ---------------------------------- Motor ----------------------------------------- |
24-gauge mild steel up to 10" 5' thru 10' 3" and larger 95 FPM 48 FPM 1-3/4" 2" (1/2" line) 90 PSI 1 HP/2 HP, 220 Volt, 1725/865 RPM, 60 Cycle, 3 Phase timing belt drive |
|
|
Online Privacy Policy
|
Copyright © 1999~2004 |